Pioneerpos AT Commands G24-LC Manuel d'utilisateur Page 363
- Page / 444
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 3: AT Commands Reference
April 15, 2008 G24-L AT Commands Reference Manual 3-299
+MSDNS, Set DNS IP Address
This command set/read DNS (Domain Name Server) IP address (primary/secondary) for each
socket. If the user doesn't specify DNS servers by AT+MSDNS, G24-L will use default DNS
from NW. The defined value(s) will be saved during disconnect PDP context (can be used in next
PDP context), but will reset after power cycle.
The following table shows the +MSDNS parameters.
Command Type Syntax Response/Action Remarks
Set
AT+MSDNS=[<Socket_id>[,
<Primary DNS server IP>
[,<Secondary DNS server
IP>]]]
OK
or:
+CME ERROR: <err>
Read
AT+MSDNS? +MSDNS: 1,<Primary DNS server
IP>,< Secondary DNS server
IP><CR><LF>
+MSDNS: 2,<Primary DNS server
IP>,< Secondary DNS server
IP><CR><LF>
+MSDNS: 3,<Primary DNS server
IP>,< Secondary DNS server
IP><CR><LF>
+MSDNS: 4,<Primary DNS server
IP>,< Secondary DNS server
IP><CR><LF>
+MSDNS: 5,<Primary DNS server
IP>,< Secondary DNS server
IP><CR><LF>
<CR><LF>
OK
Test
AT+MSDNS=? +MSDNS: (List of supported
<Socket_id>s),(<IP>),(<IP>)
Table 3-210: +MSDNS Parameters
<Parameter> Description
<Socket_id> A unique number that identifies a connection (provided
by the terminal application).
0 - Invalid socket number
1,2,3,4 - Valid socket number
5 - Valid socket number dedicated to +MPING.
<Primary DNS server IP>, <Secondary
DNS server IP>
IP of the destination site in the format
"AAA.BBB.CCC.DDD". The range of each octant is
0-255. The value can be written in 1, 2, or 3 digits.
- Technical Information 1
- Copyrights 2
- Computer Software Copyrights 2
- Trademarks 3
- Table of Contents 5
- Table of Contents 10
- List of Figures 13
- List of Figures 14
- List of Tables 15
- List of Tables 16
- Manual Scope 21
- Target Audience 21
- Manual Organization 21
- Applicable Documents 22
- Contact Us 22
- Text Conventions 22
- General Safety 23
- Keep away from live circuits 24
- Batteries 24
- Caring for the Environment 25
- Limitation of Liability 26
- Warranty Notification 27
- How to Get Warranty Service? 27
- Claiming 28
- Installed Data 29
- Out of Warranty Repairs 29
- Revision History 30
- Chapter 1: Product Features 31
- CSD Operation 32
- Improved OEM Features 33
- Set up Idle Mode Text 34
- Menu Selection 34
- Call Control by SIM 34
- TCP/UDP IP Connection 35
- Creating UDP/IP Connections 36
- Features and Benefits 37
- Technical Description 38
- Overview 38
- Short Message Service (SMS) 41
- Character Sets 43
- AT Commands Summary 45
- AT Commands Overview 57
- AT Commands Protocol 58
- AT Commands Structure 59
- Results Code Structure 60
- Command Token Types 62
- Command Argument Types 63
- Command Mode Types 63
- Aborting Commands 64
- Modem ID 65
- +CIMI, Request IMSI 69
- +CNUM, Request MSISDN(s) 70
- Read Command 71
- Table 3-3: +CNUM Parameters 71
- Capability Reporting 72
- Receiving a Data Call 74
- Call Control AT Commands 75
- DL, Dial Last Number 78
- H, Hang-up Call 79
- A, Answer Incoming Call 81
- Indication 81
- RING/+CRING Indication 82
- Table 3-7: +CRC Parameters 82
- Table 3-8: +CLIP Parameters 84
- +CCWA, Call Waiting Command 85
- Table 3-9: +CCWA Parameters 86
- • Provisioned permanently 93
- Table 3-14: +CBST Parameters 96
- &Q, Asynchronous Mode 97
- +CHUP, Hang Up Call 98
- Connection of a Voice Call 100
- Call Status Messages 103
- +CLCC, List Current Calls 104
- Execute command enables 104
- Table 3-19: +CLCC Parameters 105
- +MCST, Call Status Messages 106
- Table 3-20: +MCST Parameters 107
- +MCST Parameters 107
- +CAOC, Advice of Charge 108
- +CACM, Accumulated Call Meter 110
- Supplementary Services 114
- Table 3-26: +CSSN Parameters 115
- Table 3-29: +CUSD Parameters 117
- AT+COLP=0 121
- AT+COLP=2 121
- Phone Books and Clock 124
- Table 3-33: +CPBS Parameters 125
- +CSVM, Set Voice Mail Server 130
- Table 3-38: +MDSI Parameters 132
- Table 3-39: +MCSN Parameters 135
- Table 3-40: +CCLK Parameters 138
- SMS Commands 139
- +CMGF, Message Format 141
- Table 3-45: +CSCA Parameters 143
- Table 3-46: +CSMP Parameters 144
- Table 3-49: +CNMI Parameters 147
- Indication) 150
- +CMGL, +MMGL, List Messages 153
- +CMGR, +MMGR, Read Message 158
- GSM03.40) 161
- GSM03.40) (Cont.) 162
- Reserved bits are ignored 163
- +MMAR, Motorola Mark As Read 165
- +CMGD, Delete Message 172
- +CMGS, Send SM to Network 174
- DCS handling 177
- Network Commands 181
- +CRLP, Radio Link Protocol 182
- Table 3-76: +CREG Parameters 183
- Table 3-77: +CGREG Parameters 185
- +COPS, Operator Selection 186
- Table 3-78: +COPS Parameters 188
- +CPOL, Preferred Operators 189
- Table 3-80: +MFS Parameters 192
- Hardware Information 193
- +MBC, Battery Charger 194
- Table 3-82: +MBC Parameters 195
- +CBAUD, Baud Rate Regulation 196
- +MTDTR, DTR Line Test Command 198
- +MTCTS, CTS Line Test Command 199
- &K, RTS/CTS Flow Control 199
- &C, Circuit 109 Behavior 200
- &D, Circuit 108 Behavior 202
- +MCWAKE, GPRS Coverage 203
- ATS97, Antenna Diagnostic 207
- +MRST, Perform Hard Reset 207
- +MIOC, Motorola I/O Configure 208
- Light control example: 209
- Table 3-95: +MIOC Parameters 209
- +MIOD, Motorola I/O Define 211
- Table 3-96: +MIOD Parameters 212
- Table 3-97: Keypad GPIOs 212
- Table 3-98: +MMAD Parameters 215
- +MPCMC, Continuous PCM Clock 217
- Table 3-99: +MPCMC Parameters 218
- Audio Setup 220
- HeadSet mode 221
- Idle mode 221
- Basic Audio Setup Commands 222
- +CLVL, Loudspeaker Volume 223
- S94, Sidetone Effect 225
- S96, Echo Canceling 226
- +MAPATH, Audio Path 227
- Figure 3-6: Audio Paths 228
- +MAVOL, Volume Setting 230
- +MAMUT, Input Devices Mute 232
- +MAFEAT, Features Selection 233
- General Audio Commands 234
- +CALM, Alert Sound Mode 235
- +CRTT, Ring Type Selection 237
- +VTD, Tone Duration 239
- Access Control Commands 241
- Table 3-120: +CPIN Parameters 243
- +CPWD, Change Password 247
- +CLCK, Facility Lock 248
- Table 3-124: +CLCK Parameters 249
- Table 3-125: +EMPC Parameters 252
- Modem Register Commands 254
- Q, Result Code Suppression 255
- E, Command Echo 256
- S, Bit Map Registers 258
- Table 3-131: S2 Parameters 260
- \G, Software Control 261
- \J, Terminal Auto Rate 261
- \N, Link Type 261
- +CBAND, Change Radio Band 261
- Sleep Mode Commands 263
- Sleep Mode AT Commands 264
- Sleep Mode HW Signals 264
- WAKEUP-IN 265
- Line (pin #16) 265
- Line (pin #21) 265
- Error Handling Commands 270
- Table 3-139: +CMEE Parameters 271
- Table 3-140: +CME Errors 272
- Table 3-141: +CMS Errors 274
- Table 3-142: +STK Errors 275
- +CEER, Extended Error Report 277
- Table 3-143: +CEER Parameters 278
- UI (User Interface) 280
- &V, View Configuration 285
- &W, Store User Profile 286
- AT&W0 287
- AT&W1 287
- &Y, Default User Profile 288
- +CLAN, ME Language 289
- Table 3-149: +CLAN Parameters 290
- +CIND, Indicator Control 291
- GPRS Functionality 294
- GPRS Commands 294
- +CGDCONT, Define PDP Context 296
- For example: 297
- +CGATT, GPRS Attach or Detach 301
- +CGPADDR, Show PDP Address 302
- Table 3-159: D*99 Parameters 307
- +CGPRS, GPRS Coverage 308
- Customer 310
- Application 310
- STK Mechanisms 311
- +MTKR, Profile Download 311
- Profile Structure 312
- Table 3-183: +MTKE Parameters 321
- Table 3-185: + 323
- Send DTMF 327
- Set Up Event List 329
- Language Codes 332
- +MTKM, Motorola ToolKit Menu 336
- Control are modified 338
- Table 3-193: +MTKC Parameters 338
- +MIPCLOSE, Close a Socket 346
- +MIPSEND, Send Data 348
- +MIPSTAT, Status Report 352
- MIPXOFF, Flow Control - Xoff 352
- MIPXON, Flow Control - Xon 353
- • Power Up - 0 355
- +MSDNS, Set DNS IP Address 363
- Table 3-212: 367
- NOP - Compatible 368
- Chapter 4: Using the Commands 369
- GPRS VoiceCSD Data 370
- G24 Network Connection 371
- Test G24 Communication 371
- G24 Phonebook Download 371
- Status (Optional) 371
- RS232 Lines Setup 372
- Test G24-L Communication 373
- Basic Configuration 373
- 1. Baud setting example: 374
- SIM Card Status 375
- G24-L Network Connection 376
- Terminal Synchronization 377
- Call Control 382
- Voice Call Manipulations 384
- Conference Call 385
- Data Call 386
- Establishing GPRS PDP Context 387
- Using the ATD* Command Set 388
- Changing the Character Set 389
- Sleep Mode 390
- Get Inkey 391
- Get Input 392
- Play Tone 392
- Set Up Menu 393
- Select Item 393
- Send SMS 393
- Set Up Call 394
- Launch Browser 395
- Setup Event List 396
- TCP Data Transfer Example 397
- Xoff and Xon Example 398
- Terminal 400
- Chapter 5: Tools 401
- Tools Overview 402
- Appendix A: Reference Tables 403
- Symbol GSM (GSM 03.38) 420
- Acronyms and Abbreviations 429
- Abbreviation Full Name 431
- Numerics 435
- B - D Index 437
- N - S Index 439
- W - W Index 441
- @6802983C95@ 444
© 2020, manymanuals.fr. Tous droits réservés | 0.134 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels